2656284142@qq.com
TELL US MORE ABOUT YOUR PROJECT
Contact Sales at Zuolong
Latest products
Cutting machine boot beam jitter is what reason is caused?
by：ZORON Machinery
2021-01-29
Now you can see the shadow of the processing technology in all walks of life, cutting machine, welding machine and other processing equipment is becoming more and more widely applied.
But in many customers to use when cutting machine, because the cutting machine are not familiar with or improper operation and appear boot reset the wrong direction, beam jitter and a series of problems.
Above for the cause of the problem in small make up today sort out solution for you!
1, check whether beam offset serious, both sides shall not be greater than 2 mm, see both sides of the wheel bearing has no damage, driving is smooth.
2, boot check the jitter in the shaft, car or beam, disconnect a shaft power test another shaft motors and drives ( Block) If there is a fault. Interchangeable test, find out the problems existed in the motor or drive ( Block) 。
3, if change after cutting machine drive, a reset is not normal, should first check the parameter setting is correct, by changing the main parameters, can solve the problem of reset is not normal.
4, push the car look have friction or shake, if there is a slider gap is too big, need more replacement sliders.
5, turn it off by hand to push the car and beam, to see whether there is resistance, the obstacle is clear or packed, if any, and see if the left tension wheel is tight.
6, with a resistance model, to measure the resistance. If no need to change resistance.
7, check the synchronous belt, bald, blowpipe, drag chain is stuck.
8, when the cutting machine is reset in the right direction, but in the end, the car or beam could not stop the impact machine. Need to check the motherboard parameter errors. Sensor sensor wire is broken or damaged, the magnet is in the reasonable location.
9, whether the dust on the machine guide rail is too much and hindering the car, clean up dirt add lubricating oil to the slider.
10, such problems still exist, may for the mainboard failure, need to change cutting machine control board. Check the motor and the drive ( Block) Whether connected line contact is good.
reset is not normal, beam jitter, above is cutting machine boot of fault analysis and solutions of the wall, hope to be of help! ZuoLong machinery as a professional manufacturer of cutting machine, has for the automobile manufacturing, rail transportation, engineering machinery, agricultural machinery, elevator manufacturing, food and food machinery, pharmaceutical machinery, aerospace and military industry, petroleum machinery, metal structure and professional sheet metal processing industries created value and interests.
we want more cutting machine price, welcome to inquire, hotline:
1, check whether beam offset serious, both sides shall not be greater than 2 mm, see both sides of the wheel bearing has no damage, driving is smooth.
2, boot check the jitter in the shaft, car or beam, disconnect a shaft power test another shaft motors and drives ( Block) If there is a fault. Interchangeable test, find out the problems existed in the motor or drive ( Block) 。
3, if change after cutting machine drive, a reset is not normal, should first check the parameter setting is correct, by changing the main parameters, can solve the problem of reset is not normal.
4, push the car look have friction or shake, if there is a slider gap is too big, need more replacement sliders.
5, turn it off by hand to push the car and beam, to see whether there is resistance, the obstacle is clear or packed, if any, and see if the left tension wheel is tight.
6, with a resistance model, to measure the resistance. If no need to change resistance.
7, check the synchronous belt, bald, blowpipe, drag chain is stuck.
8, when the cutting machine is reset in the right direction, but in the end, the car or beam could not stop the impact machine. Need to check the motherboard parameter errors. Sensor sensor wire is broken or damaged, the magnet is in the reasonable location.
9, whether the dust on the machine guide rail is too much and hindering the car, clean up dirt add lubricating oil to the slider.
10, such problems still exist, may for the mainboard failure, need to change cutting machine control board. Check the motor and the drive ( Block) Whether connected line contact is good.
reset is not normal, beam jitter, above is cutting machine boot of fault analysis and solutions of the wall, hope to be of help! ZuoLong machinery as a professional manufacturer of cutting machine, has for the automobile manufacturing, rail transportation, engineering machinery, agricultural machinery, elevator manufacturing, food and food machinery, pharmaceutical machinery, aerospace and military industry, petroleum machinery, metal structure and professional sheet metal processing industries created value and interests.
we want more cutting machine price, welcome to inquire, hotline:
Custom message
